Mechanical and thermal properties of PMMA resin composites for interim fixed prostheses reinforced with calcium β-pyrophosphate

Iouliana Chrysafi; Eleana Kontonasaki; Antonios D Anastasiou; Dimitra Patsiaoura; Lambrini Papadopoulou; George Vourlias; Evangelia Vouvoudi; Dimitrios Bikiaris

doi:10.1016/j.jmbbm.2020.104094

Mechanical and thermal properties of PMMA resin composites for interim fixed prostheses reinforced with calcium β-pyrophosphate

J Mech Behav Biomed Mater. 2020 Dec:112:104094. doi: 10.1016/j.jmbbm.2020.104094. Epub 2020 Sep 17.

Authors

Iouliana Chrysafi¹, Eleana Kontonasaki², Antonios D Anastasiou³, Dimitra Patsiaoura¹, Lambrini Papadopoulou⁴, George Vourlias¹, Evangelia Vouvoudi⁵, Dimitrios Bikiaris⁵

Affiliations

¹ Laboratory of Advanced Materials and Devices, Department of Physics, Faculty of Sciences, Aristotle University of Thessaloniki, Thessaloniki, GR-54124, Macedonia, Greece.
² Section of Prosthodontics, Department of Dentistry, Faculty of Health Sciences, Aristotle University of Thessaloniki, Thessaloniki, GR-54124, Macedonia, Greece. Electronic address: kont@dent.auth.gr.
³ Department of Chemical Engineering and Analytical Science, University of Manchester, Manchester M1 3AL, UK.
⁴ Section of Mineralogy-Petrology-Economic Geology, Department of Geology, Faculty of Sciences, Aristotle University of Thessaloniki, Thessaloniki, GR-54124, Macedonia, Greece.
⁵ Laboratory of Polymers Chemistry and Technology, Department of Chemistry, Faculty of Sciences, Aristotle University of Thessaloniki, GR-54124, Macedonia, Greece.

PMID: 32979608
DOI: 10.1016/j.jmbbm.2020.104094

Abstract

Interim restorations are essential in fixed prosthodontics as they provide temporary protection of teeth before the insertion of the permanent restoration. Poly(methyl methacrylate) (PMMA) is widely used in the fabrication of interim-fixed restorations as it is a biocompatible material with a lot of convenient properties. However, it exhibits low impact and tensile strength and therefore it is necessary to be reinforced. Calcium β-pyrophosphate (β-CPP) is considered a promising reinforcing material for dental applications, especially for enamel regeneration due to its stability at low pH and its low wear rate. The aim of this study was to manufacture PMMA/β-CPP composites suitable for fixed-interim restorations and to study their mechanical and thermal properties. In order to enhance β-CPP dispersion into PMMA matrix, ball-milling was performed for 1 or 6 h. Three-point bending test was performed to study flexural strength, Dynamic Mechanical Analysis (DMA) to reveal the elastic and viscous moduli along with T_g, Fourier Transform Infrared Spectroscopy (FTIR) and X-Ray Diffraction Analysis (XRD) to investigate the structure of the materials and SEM for the morphological evaluation of both composite powders and polymerized specimens. Thermogravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC) experiments were performed to study their thermal properties. A statistically significant increase in flexural strength was found in the 0.5, 0.75 and 1% composite groups after 6 h ball-milling, relative to the control, with the 6 h ball milling mixed specimens, presenting the highest flexural strength values. The brittle fracture type was common to all groups. An obvious improvement of the mechanical properties and a slight improvement in the thermal stability of the composite materials values were also observed as β-CPP content was increased, while T_g values were statistically not-affected.

Keywords: Calcium β-pyrophosphate; Flexural strength; Glass transition temperature; Interim dental restorations; Poly(methyl methacrylate); Polymeric composites.

MeSH terms

Calcium Pyrophosphate
Calcium*
Composite Resins
Dental Materials
Diphosphates
Materials Testing
Pliability
Polymethyl Methacrylate*
Prostheses and Implants
Stress, Mechanical
Surface Properties

Substances

Composite Resins
Dental Materials
Diphosphates
Polymethyl Methacrylate
Calcium
Calcium Pyrophosphate