Low-Temperature-Processed Brookite-Based TiO2 Heterophase Junction Enhances Performance of Planar Perovskite Solar Cells

Md Shahiduzzaman; Sem Visal; Mizuki Kuniyoshi; Tetsuya Kaneko; Shinjiro Umezu; Tetsuhiro Katsumata; Satoru Iwamori; Masato Kakihana; Tetsuya Taima; Masao Isomura; Koji Tomita

doi:10.1021/acs.nanolett.8b04744

Low-Temperature-Processed Brookite-Based TiO₂ Heterophase Junction Enhances Performance of Planar Perovskite Solar Cells

Nano Lett. 2019 Jan 9;19(1):598-604. doi: 10.1021/acs.nanolett.8b04744. Epub 2018 Dec 26.

Authors

Md Shahiduzzaman¹, Sem Visal, Mizuki Kuniyoshi, Tetsuya Kaneko, Shinjiro Umezu², Tetsuhiro Katsumata, Satoru Iwamori, Masato Kakihana³, Tetsuya Taima¹, Masao Isomura, Koji Tomita

Affiliations

¹ Nanomaterials Research Institute , Kanazawa University , Kanazawa 920-1192 , Japan.
² Department of Modern Mechanical Engineering , Waseda University , Tokyo 169-8555 , Japan.
³ Institute of Multidisciplinary Research for Advanced Materials , Tohoku University , Sendai 980-8577 , Japan.

PMID: 30582702
DOI: 10.1021/acs.nanolett.8b04744

Abstract

In the design of electron-transport layers (ETLs) to enhance the efficiency of planar perovskite solar cells (PSCs), facile electron extraction and transport are important features. Here, we consider the effects of different titanium oxide (TiO₂) polymorphs, anatase and brookite. We design and fabricate high-phase-purity, single-crystalline, highly conductive, and low-temperature (<180 °C)-processed brookite-based TiO₂ heterophase junctions on fluorine-doped tin oxide (FTO) as the substrate. We test and compare single-phase anatase (A) and brookite (B) and heterophase anatase-brookite (AB) and brookite-anatase (BA) as ETLs in PSCs. The power-conversion efficiencies (PCEs) of PSCs with low-temperature-processed single-layer FTO-B as the ETL were as high as 14.92%, which is the highest reported efficiency of FTO-B-based single-layer PSC. This implies that FTO-B serves as an active phase and can be a potential candidate as an n-type ETL scaffold in planar PSCs. Moreover, the surface of highly crystalline brookite TiO₂ exhibits a tendency toward interparticle necking, leading to the formation of compact scaffolds. Furthermore, PSCs with heterophase junction FTO-AB ETLs exhibited PCEs as high as 16.82%, which is superior to those of PSCs with single-phase anatase (FTO-A) and brookite (FTO-B) as the ETLs (13.86% and 14.92%, respectively). In addition, the PSCs with FTO-AB exhibited improved efficiency and decreased hysteresis compared with those with FTO-BA (13.45%) due to the suitable band alignment with the perovskite layer, which resulted in superior photogenerated charge-carrier extraction and reduced charge accumulation at the interface between the heterophase junction and perovskite. Thus, the present work presents an effective strategy by which to develop heterophase junction ETLs and manipulate the interfacial energy band to further improve the performance of planar PSCs and enable the clean and eco-friendly fabrication of low-cost mass production.

Keywords: Low-temperature processing; TiO2 heterophase junction; brookite TiO2 nanoparticles; planar perovskite solar cells.

Publication types

Research Support, Non-U.S. Gov't